Reference chart showing flag ratio families and nominal sizes converted to centimetres
Flags & Banners

Flag Sizes and Common Ratios: A Reference for Buyers

Two numbers decide what a flag looks like in place: its size and its ratio. Buyers almost always specify the first and forget the second — which is how a flag arrives the right size and still looks wrong on the pole.

Short answer: the standard outdoor flag is 3 × 5 ft (91 × 152 cm) in a 2:3 ratio — that is the size most house poles are built around. “Standard” is really two numbers: a nominal size and a ratio. The same 3 ft hoist becomes 6 ft long at 1:2 and 5 ft long at 3:5, so the ratio decides the finished dimensions even when the nominal size does not change.

Flag size chart: ratio against finished dimensions

Read across from the ratio you need to the finished size at a given hoist. These are exact multiples, not nominal trade names — useful when a customer specifies “150 cm” or sends a design file rather than a 3 × 5.

Ratio (hoist : fly) At 90 cm hoist At 150 cm hoist Typical use
1 : 2 90 × 180 cm 150 × 300 cm UK and many Commonwealth national flags
2 : 3 90 × 135 cm 150 × 225 cm The default for corporate and promotional flags; most European national flags
3 : 5 90 × 150 cm 150 × 250 cm German national proportions; squarer, reads better from the side
5 : 8 90 × 144 cm 150 × 240 cm A compromise between 2:3 and 3:5
10 : 19 90 × 171 cm 150 × 285 cm US national flag proportions

Two checks before you send a size: multiply the hoist by the ratio to confirm the fly, and compare the result against the pole’s rated capacity rather than the space on the wall. A flag is a sail — a longer fly at the same hoist adds area and load without looking any taller.

Reference chart showing flag ratio families and nominal sizes converted to centimetres

Ratio: the number nobody specifies

Ratio is length-to-height. It is not a style choice — it comes out of the design:

  • A flag built to a squarer ratio looks taller and fuller on the pole.
  • A flag built to a longer ratio looks narrower and flies further out from the pole.
  • The same nominal size in two different ratios uses different amounts of fabric and puts different load on the pole.

This matters most when a flag is being reproduced. If you are making a national flag, the official ratio is part of the design and must not be adjusted to fit a convenient size — a national flag made to the wrong ratio is a compliance problem, not a design preference. Send the design file and the ratio comes with it.

For corporate and promotional flags there is no fixed ratio, and this is where the choice is genuinely free. Decide it against the pole and the viewing distance, not against a supplier’s stock list.

Nominal sizes and their metric equivalents

Outdoor flags are normally ordered by nominal imperial size. The conversions below are what those names actually measure:

Nominal size Metric equivalent Typical use
2 × 3 ft 61 × 91 cm Hand-held, small indoor display, boat staffs
3 × 5 ft 91 × 152 cm The most common house-pole size
4 × 6 ft 122 × 183 cm Larger house poles, low commercial poles
5 × 8 ft 152 × 244 cm Commercial poles
6 × 10 ft 183 × 305 cm Large commercial poles, high-wind exposure sites

Hand and desk flags are quoted in millimetres or centimetres instead, because the nominal trade sizes do not apply at that scale. Our confirmed sizes are listed further down.

Which size for which job

Application Size driver
Hand-held and event giveaway Reach and weight — a flag that gets waved cannot be heavy
Desk and conference table Table footprint and how many flags sit in one row
House pole Pole height and the pole’s rated load
Commercial pole Pole height, windspeed exposure, and the halyard and truck rating
Feather and banner flags Banner height, which is set by the flag’s own format rather than by a ratio
Vehicle and window The mounting surface — the flag cannot be larger than the mount can carry

Size and the pole: where most orders go wrong

A flag is a sail. The load it puts on a pole, a bracket or a fitting scales with the flag’s area, so the relationship is not linear:

> Doubling a flag’s linear size roughly quadruples its sail area — and the load it puts on the pole and fittings.

Diagram comparing an oversized flag on a bent pole with a flag matched to the pole it was specified for

That is why an oversized flag on a light staff is the single most common cause of hardware damage, and why the flag’s hoist should be kept in proportion to the staff or halyard it hangs from.

Two practical consequences:

  1. Never upsize the flag without upsizing the pole or mount. The pole has a rated capacity, and the flag is the load.
  2. Wind exposure decides more than size does. A 3 × 5 ft flag on an exposed site can load its pole harder than a 5 × 8 ft flag in a sheltered courtyard.

The sizes we build

These are the sizes confirmed against our own product range:

Product Size
Hand and stick flags 150 × 100 mm, 210 × 140 mm, 200 × 300 mm
Table and desktop flags 14 × 21 cm (custom sizes available)
Car window flag 30 × 45 cm
Magnetic car flag 14 × 21 cm
Feather flag format (complete set) 0.7 × 3.8 m banner on a 4.3 m pole

Choosing between two sizes

When a buyer is torn between two sizes on the same pole, three questions settle it:

  1. How far away will people see it? A flag reads at roughly its own height in distance terms; if viewers are 20 m away, a small flag is not a small version of a big one, it is an unreadable one.
  2. What is the pole rated for? The pole’s capacity sets the maximum, not the customer’s preference.
  3. What happens in the worst week of the year, not the average week? Wind is what breaks flags and poles; size is what decides how much of it the pole takes.

Where to go next

This page is the reference; these go deeper on the specific decision in front of you:

Get a quotation

Send the intended use, the pole (or the mount) and the design file, and we will confirm the size, the ratio and the attachment as one specification. Custom sizes and custom ratios sit under our OEM / ODM service.

Related reading




Related Articles

Need a Quote for Your Project?

Tell us your specification, quantity and target market. Our engineering team replies within 24 hours with a quotation, an artwork proof and production lead time.